Raymarine 425 Spezifikationen Seite 91
- Seite / 114
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 5: Installation 5-9
1. Loosen the trunnion knobs and remove the trunnion from the display
unit.
2. Mark the locations of the trunnion screw holes on the mounting sur-
face.
3. Use the screws supplied to fix the trunnion at the marked locations.
4. Fit the unit to the trunnion, adjust the display angle and tighten the
knobs.
Panel Mounting
CAUTION:
Make sure that there are no hidden electrical wires or other items
behind the location before proceeding. Make sure that there is
sufficient rear access for mounting and cabling. Allow at least
4cm at the right hand side of the display to enable chart cards to
be inserted and removed.
The unit can be panel mounted, using the panel-mounting kit (accessory)
available from your local Raytheon dealer.
➤ Panel mount the unit as follows:
1. Check the selected location for the unit. A clear, flat area at least 7in
(175mm) wide by 7½in (190mm) high, with at least 3½in (90mm) of
clearance behind the panel, is required.
2. Using the supplied template, trace out the display unit cut-out and
mark the drilling centres for the four securing holes outside of the
cut-out area.
3. To provide start holes for removing the cut-out, drill four
3
/
8
in
(10mm) holes in each opposing corner and four
1
/
4
in (6mm) holes for
the two trunnion lug clearance slots in the cut-out area.
4. Using a suitable saw, cut along the inside edge of the cut-out line.
5. With the trunnion (yoke) and knobs removed, make sure that the unit
fits in the cut-out area.
6. Drill out the four
3
/
16
in (5mm) securing holes as indicated on the tem-
plate. It is recommended that a
1
/
16
in (1mm) pilot hole is drilled first.
7. Screw the studs into the vacant holes at the rear of the unit, hand tight
only.
8. Place the gasket on the unit and slide the unit into the panel cut-out.
9. Secure the unit with the thumb nuts, hand tight only (Figure 5-5).
- Raychart 425 1
- Chartplotter 1
- Raychart 425 Chartplotter 3
- Owner’s Handbook 3
- Warranty 4
- EMC Conformance 4
- Technical Accuracy 4
- Chapter 1: Overview 9
- 1-2 Raychart 425 Chartplotter 10
- Figure 1-1: WAAS Coverage Map 10
- How it Works 11
- 1.3 The Chartplotter 12
- Operating Controls 13
- Trackpad and Cursor 14
- Dedicated Keys 15
- Function Bar 15
- Pop-Up Menus 16
- Database Lists 16
- Chapter 2: Getting Started 17
- 2.2 Switching On/Off 18
- 2.3 Chart Simulator 19
- 2.4 Controlling the Display 20
- Figure 2-3: Display Modes 21
- ➤ To centre the vessel: 22
- Changing the Chart Scale 23
- 2-8 Raychart 425 Chartplotter 24
- RANGE key as 24
- Inserting a Nav-Chart Card 25
- Removing a Nav-Chart card 26
- Displaying the Chart Data 26
- Chapter 3: Operation 27
- ➤ To place a new waypoint: 28
- WAYPOINT 28
- SIM OV NU 29
- Selecting a Waypoint 30
- ➤ To display waypoint data: 31
- Erasing Waypoints 33
- 3.3 Working with Routes 34
- 35
- Creating a New Route 36
- Saving the Current Route 37
- Erasing or (re)Naming a Route 40
- Editing a Route 40
- Follow a Route 43
- Reverse a Route 43
- Target Point Arrival 44
- Alter a Route 44
- ➤ To advance to a waypoint: 45
- ➤ To restart XTE: 46
- Go to Cursor 47
- Go to a Port 48
- 3.5 Changing the Display Mode 49
- ➤ To change the display mode: 50
- BDI Display 51
- BRG 234° T 52
- RNG 12.4 nm 52
- Navigation Data 53
- 50°45.252 N 54
- 1°06.000 W (c) 54
- COG 230° T 54
- SOG 6.8 Kts 54
- TIME 12:34 55
- DATE 26/01/99 55
- Displayed Waypoints 56
- 3.7 Using Tracks 58
- Setting up a Track 59
- ➤ To set up a track: 60
- ➤ To clear the current track: 60
- SmartRoute 61
- Port Services 61
- Tide Information 62
- ➤ To obtain Tide Height Data: 63
- ➤ To display Sun/Moon data: 64
- NANTUCKET 65
- NANTUCKET HARBOR 66
- 3.9 Man Overboard (MOB) 68
- Table 3-1: Alarm Settings 69
- Chapter 4: Setting Up 71
- Bearing Mode 73
- Key Beep 73
- Variation 73
- Date Format 74
- Time Offset 74
- Language 74
- Simulator 74
- Simulated SOG 74
- 4.3 Chart Set Up Parameters 75
- Plotter Mode 77
- Show Waypoints 77
- Orientation 77
- 4-8 Raychart 425 Chartplotter 78
- ➤ To select GPS Set Up: 80
- Chapter 4: Setting Up 4-11 81
- SD GPS SET UP 82
- Chapter 5: Installation 83
- Suppression Ferrites 84
- Items Missing? 85
- Registering this Product 85
- GPS Receiver Installation 85
- Surface Mounting 86
- Top view 87
- Underside view 87
- 5-6 Raychart 425 Chartplotter 88
- Chapter 5: Installation 5-7 89
- Trunnion (yoke) Mounting 90
- Panel Mounting 91
- 5.4 Cable Running 92
- Connectors 93
- System Check 95
- Initial Switch On 95
- WARNING: 97
- ➤ To perform a factory reset: 98
- 6.4 Worldwide Support 99
- 6-4 Raychart 425 Chartplotter 100
- CAUTION: 103
- B-2 Raychart 425 Chartplotter 104
- Appendix C: NMEA Data 105
- C-2 Raychart 425 Chartplotter 106
- D-2 Raychart 425 Chartplotter 108
- SiRF LICENSE AGREEMENT 109
- IMPORTANT - READ CAREFULLY: 109
- Installation Templates T-1 111
- T-2 Raychart 425 Chartplotter 112
- Installation Templates T-3 113
- T-4 Raychart 425 Chartplotter 114
Verwandte Produkte und Handbücher für Navigatoren Raymarine 425
Navigatoren Raymarine Raynav 575 Bedienungsanleitung
(149 Seiten)
(149 Seiten)
Navigatoren Raymarine ST7002 Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Navigatoren Raymarine ST8002 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Navigatoren Raymarine GPS navigation Spezifikationen
(156 Seiten)
(156 Seiten)
Navigatoren Raymarine AIS500 Bedienungsanleitung
(48 Seiten)
(48 Seiten)
Navigatoren Raymarine SL520 Spezifikationen
(170 Seiten)
(170 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern